Touch Dimmer Switch 2 Pack, 3 Way Touch Control Modules, Replacement Sensor with 3 Levels Dimming Function, Desk Lamp Switch Repair Kits with Wire Caps, Fit Dimmable LED, Incandescent, Halogen Bulbs

Good quality fo the price. Simple instructions for installing the module. It can be a little finicky regarding the type of light bulbs used. Incandescent are good, but if you are using LED bulbs, it workd best with a higher wattage and the Fiet brand.

I bought another brand, and after 2 weeks it became possessed. It would constantly change brightness and go on/off at will. I replaced it with this unit, and VOILA!!! It works great. Very happy with this one and the seller. Super easy 4 wire connections and you're done. I solder all of my connections, but you do NOT have to. That's just my electronic OCD background. LOL

One of the two sensors blew when I first hooked it up and tested it. I ruined it. YOU MUST follow the instructions. I carefully marked my wires on the lamp with the old unit still attached and hooked the new one up the same way, using the same color pattern. The wires were all the same colors on the old and the new unit, so I figured this would be the best way to install. This was not how the instructions said to do it. That was my fault. When I followed the instructions on the 2nd unit, it worked fine. FOLLOW the instructions.

Arrived on-time and as advertised. Have not installed yet so no comment on functionality or reliability.

I don't do a lot of reviews (usually positive ones!) but felt I should definitely writet this one.I have had my touch lamps for going on 20 years. I love them, but the touch switch does go bad after some time (it varies- 5- 10 yrs) and I have replaced the switches in each lamp before, it is fussy work but not that hard. I could not remember the brand of touch switches I had purchased in the past (,they were the same as what came in it originally) but found these here on amazon and they looked right.So. even though it was obvious these switches are of inferior quality compared to the switch I removed, I put the new one in. The wires in this unit are NOT copper (which the original brand has always been). Put everything back together as usual, did nothing different, wires seemed to match what was being replaced and directions. Tried the lamp....there was a huge 'pop' immediately and it caused the circuit breaker to trip. Almost 20 yrs and this has NEVER happened before. Scary Junk.Says right on the lamp not to use any bulbs bigger than 25 watts, and I always use/only have 15 watt bulbs so that was not an issue. I figured out the original switch was from OK Lighting, and will stick with their great quality product from now on. Will NOT purchase this brand again.

I've used these in several of my lamps now and for anyone wondering - like I was - they will work just fine if your lamp has a painted metal body. Other than that, everything has worked as advertised. Will definitely use again in future projects.

Purchased four of these all work perfectly.Three of them are wired to picture lights above paintings in my home.The fourth I wired to my china cabinet.One user wired to his china cabinet and some how was able to attach the GREEN sensor wire to a hinge, thus turning on the lights with just a touch of the hinge he chose.After wiring the unit, I attached the unit to the back of my china cabinet closer to right edge, using mounting tape.I then purchased some metal tape from the hardware store (very easy to find)I unrolled a length of approx 20 inches and taped the green sensor wire off the switch to the back edge of the cabinet.The reason I chose random length 20 inches?This way all I have to do is touch the tape anywhere within the 20 inches and the lights will come on.No hunting for the sensor that way.In short the green sensor wire in this case triggers the lights when it comes in contact with your finger.Using the metal tape works as a conductor and is completely safe.

Very easy install, took only 5-7 minites to install in two lamps, but you can tell where it lacks quality. After installing one of my lamps turns on when you touch it, but additional touches don't change brightness or turn it off. It will not turn off until unplugged. Only half in the pack worked, so I give it half stars