LEDKINGDOMUS Front& Rear Bumper Compatible 07-18 Jeep Wrangler JK &Unlimited Rock Crawler 4X LED Lights w/Winch Plate D-rings, 2x LED Lights & 2" Hitch Receiver, Black, length 61.54" for jk

The Rugged Ridge bumper that came with my wrangler jk would not accept a winch. I ordered this as a replacement and mated it with a Badlands 1200 Winch from Harbor Freight. It was delivered in good shape without damage. Installation of the bumper was simple and straight forward. Everything lined up without modification. Mounting the winch was not easy. It required two sets of hands to get things lined up and bolted on. But thru no fault of the bumper design.This bumper is not as heavy and sturdy as my previous bumper. So we will see how it does long term. But if you are on a budget, or feel you do not require a heavy duty bumper for your purposes, then I think this is a good choice.

The bumper arrived packaged well and undamaged. It had all the necessary hardware and easy to follow instructions. I did however have to use a step bit to widen one set of holes only by about ⅛ of inch to allow the bolt to start. The bottom bracket hangs lower than the frame, I suspect this may be because of differences between the TJ and YJ models ( this bumper is said to fit both and has two sets of mounting holes). But the bottom bracket easily tightened up against the frame. If you are mounting a winch on this bumper save yourself some time and mount it before you mount the bumper on the TJ model like mine once the bumper is mounted you will find the rear bolt holes obscured from underneath so mount the winch and then mount the bumper. Overall I am happy with the look. As for winching on this bumper I have not yet had to use that so only time will tell. I read other reviews that said they had good look and found the bumper to be sturdy enough to winch hard without doing any damage. This was a pretty easy install however you will need a very shallow ratchet or a box end wrench to install the upper bolts as the clearance is pretty tight. For the price I am happy with the bumper and would gladly buy it again.

Kinda hard to wire the bumper lights but it worked

Looks great and fills in the gap between the bumper and fender.

Bumper on a budget is what prompted this purchase. 17 yr old son's jeep and he buys as he saves his money and summer jobs don't allow for top shelf purchases every time.Pros:1. The bumper looks good overall.2. Finish is good and the welds seem to be pretty good, but I may not be the best judge for that but I've seen some horrible welds and these do not fit the description.Cons:1. The holes for my '94 YJ had to be ground out a little on the bottom and the top, maybe an 1/8th +/- but for only one side. Seems one side would match but the opposite is off.2. The LED's are not bright, but we attached them to the low beam side of the headlights in hopes on those foggy nights coming home it'll light up a little more.3. Couldn't use the bolts with the bumper, reused the old stock bolts. Threads appear to be diff but I dont have a tool to measure. When trying to use the bolts w/ the bumper seems they wanted to cross thread. Buffed out the old bolts and went in w/o issue.Neither pro/con but I've seen some complaints about not being 5/32 so I took some measurements, see attached pics. One is at the rear of the top plate nearest the radiator. Second is the winch cable guide plate and final the bottom of the bumper.Again, it's not a high end bumper but it serves the purpose and eventually we'll dress it up w/ a winch.Should anything change I'll amend the review.

Just installed this bumper over the weekend. It was pretty easy, not as heavy as I was hoping it to be but it’s an improvement over stock. Uninstalling the original bumper wasn’t to bad, just have some deep sockets and shoot the stock bolts with some penetrating oil first, it will make it a lot easier. The finish on it is a little rough and parts of it were already scratched off so I used some Mopar touch up paint on it and it seems to blend well. Everything lined up but my vacuum pump is right up against the bumper. The bull bar is bolted on with silver nuts and bolts so I will be spraying those with matte black next along with the vacuum pump. I have read the reviews about this rusting and understand, I have a Nilight rear bumper and it is much heavier and the finish is much thicker on the powder coat. The fog lights installed using the stock screws from the oem fog lights without issue. I tried to use a harness to extend the wires but purchased the incorrect one, I still got them to work but will order a replacement very soon. I did have a skid plate on but had to remove it cause it would not fit. This bumper has a couple tabs near the winch plate that block the skid plate from getting under the bumper. For the price I am happy with it. I put on a few coats of ceramic coating hoping this will prevent rust.

This review is for the LedKingdomUS full width front bumper. Overall I am very happy with this bumper. I had previously bought a different bumper from a different manufacturer that claimed it to be a full width bumper and when I installed it the bumper wasn’t as wide as the OE fenders and looked wrong to me because of the way it cut upward close to the fender to allow for more clearance. So I returned it and skeptically ordered this one. I say I was skeptical because it looked the same as the other one so my initial thought was this one was from the same manufacturer with a different name on it. Well I am happy to say I was wrong. THIS BUMPER IS A TRUE FULL WIDTH BUMPER. The reason I gave it 4 stars instead of 5 is it’s a little light in comparison to some of the other bumpers out there. (We’ve installed a few different brands at the shop for our customers.)I know some people like that though, to try to keep the weight off the nose, especially when throwing a hundred pound winch up there. So far we’ve been pulled out of trouble and my wife hit a tree while we were wheelin’ and it’s barely got a scratch on it. The bumper hasn’t even so much as flinched. The D-rings don’t come with isolators and there were no nuts and bolts for the fog lights in the package. I didn’t want to use the crappy OE self tappers so a quick trip to Home Depot and I was good to go on the new nuts and bolts.

Bought the same bumper a year ago for 389.00I'm amazed at the price increaseMy wife hit a deer with the old one it did protect the Jeep better then the stock one would have ,but it should have held up better then it did .